ok

ok

boot/config-35-480X320.txt

@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 480 320 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-35-600X400.txt

@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 600 400 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-35-720X480.txt

@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 720 480 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-35-810X540.txt

@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 810 540 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-35-960X640.txt

@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 960 640 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-35.txt

@@ -54,5 +54,5 @@ enable_uart=1
 
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
-dtoverlay=tft35a:rotate=90
+dtoverlay=tft35a
 dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=1,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-35DPI.txt

@@ -0,0 +1,73 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+display_rotate=1 
+dtoverlay=qddpi24     
+overscan_left=0
+overscan_right=0
+overscan_top=0
+overscan_bottom=0
+framebuffer_width=480
+framebuffer_height=320
+enable_dpi_lcd=1
+display_default_lcd=1    
+dpi_group=2
+dpi_mode=87     
+dpi_output_format=0x07f003
+hdmi_timings=321 0 28 18 28 480 0 2 2 4 0 0 0 60 0 32000000 6
+
+dtoverlay=ads7846,cs=1,penirq=18,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-43.txt

@@ -56,7 +56,7 @@ enable_uart=1
 dtparam=audio=on
 max_usb_current=1
 display_rotate=0
-hdmi_drive=1
+max_usb_current=1
 hdmi_group=2
 hdmi_mode=87
 hdmi_timings=480 0 1 41 2 272 0 2 10 2 0 0 0 60 0 9000000 3

boot/config-5.txt

@@ -55,7 +55,6 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
-hdmi_drive=1
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87

boot/config-7B-800x480.txt

@@ -55,7 +55,6 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
-hdmi_drive=1
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87

boot/config-7C-1024x600.txt

@@ -55,7 +55,6 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
-hdmi_drive=1
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87