ok

2017-06-16 11:38:15 +08:00
parent 33907b4cf2
commit b8c3838ed3
28 changed files with 722 additions and 11 deletions
@@ -1,4 +1,5 @@
-sudo mkdir -p /etc/X11/xorg.conf.d
+#!/bin/bash
+sudo mkdir /etc/X11/xorg.conf.d
 sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/
 sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/tft9341.dtbo
 sudo cp -rf ./usr/99-calibration.conf-28  /etc/X11/xorg.conf.d/99-calibration.conf
@@ -6,4 +7,23 @@ sudo cp -rf ./usr/99-fbturbo.conf  /usr/share/X11/xorg.conf.d/
 sudo cp ./usr/cmdline.txt /boot/
 sudo cp ./usr/inittab /etc/
 sudo cp ./boot/config-28.txt /boot/config.txt
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
 sudo reboot
@@ -1,4 +1,5 @@
-sudo mkdir -p /etc/X11/xorg.conf.d
+#!/bin/bash
+sudo mkdir /etc/X11/xorg.conf.d
 sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/
 sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/tft9341.dtbo
 sudo cp -rf ./usr/99-calibration.conf-32  /etc/X11/xorg.conf.d/99-calibration.conf
@@ -6,4 +7,23 @@ sudo cp -rf ./usr/99-fbturbo.conf  /usr/share/X11/xorg.conf.d/
 sudo cp ./usr/cmdline.txt /boot/
 sudo cp ./usr/inittab /etc/
 sudo cp ./boot/config-32.txt /boot/config.txt
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
 sudo reboot
@@ -1,4 +1,5 @@
-sudo mkdir -p /etc/X11/xorg.conf.d
+#!/bin/bash
+sudo mkdir /etc/X11/xorg.conf.d
 sudo cp ./usr/tft35a-overlay.dtb /boot/overlays/
 sudo cp ./usr/tft35a-overlay.dtb /boot/overlays/tft35a.dtbo
 sudo cp -rf ./usr/99-calibration.conf-35  /etc/X11/xorg.conf.d/99-calibration.conf
@@ -6,4 +7,23 @@ sudo cp -rf ./usr/99-fbturbo.conf  /usr/share/X11/xorg.conf.d/
 sudo cp ./usr/cmdline.txt /boot/
 sudo cp ./usr/inittab /etc/
 sudo cp ./boot/config-35.txt /boot/config.txt
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
 sudo reboot
@@ -0,0 +1,31 @@
+#!/bin/bash
+sudo cp -rf ./boot/config-35DPI.txt /boot/config.txt
+sudo cp ./usr/bcm2709-rpi-2-b.dtb /boot/
+sudo cp ./usr/bcm2710-rpi-3-b.dtb /boot/ 
+sudo cp ./usr/cmdline.txt /boot/
+sudo cp ./usr/qddpi24.dtb /boot/overlays/
+sudo cp ./usr/qddpi24.dtb /boot/overlays/qddpi24.dtbo
+sudo cp ./usr/inittab /etc/
+sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
+sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo cp -rf ./usr/99-calibration.conf-3508 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
+sudo reboot
@@ -0,0 +1,27 @@
+#!/bin/bash
+sudo cp -rf ./boot/config-35-480X320.txt /boot/config.txt 
+sudo cp ./usr/cmdline.txt /boot/
+sudo cp ./usr/inittab /etc/
+sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
+sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo cp -rf ./usr/99-calibration.conf-3508 /etc/X11/xorg.conf.d/99-calibration.conf
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
+sudo reboot
@@ -0,0 +1,27 @@
+#!/bin/bash
+sudo cp -rf ./boot/config-35-600X400.txt /boot/config.txt 
+sudo cp ./usr/cmdline.txt /boot/
+sudo cp ./usr/inittab /etc/
+sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
+sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo cp -rf ./usr/99-calibration.conf-3508 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
+sudo reboot
@@ -0,0 +1,27 @@
+#!/bin/bash
+sudo cp -rf ./boot/config-35-720X480.txt /boot/config.txt 
+sudo cp ./usr/cmdline.txt /boot/
+sudo cp ./usr/inittab /etc/
+sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
+sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo cp -rf ./usr/99-calibration.conf-3508 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
+sudo reboot
@@ -0,0 +1,27 @@
+#!/bin/bash
+sudo cp -rf ./boot/config-35-810X540.txt /boot/config.txt 
+sudo cp ./usr/cmdline.txt /boot/
+sudo cp ./usr/inittab /etc/
+sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
+sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo cp -rf ./usr/99-calibration.conf-3508 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
+sudo reboot
@@ -0,0 +1,27 @@
+#!/bin/bash
+sudo cp -rf ./boot/config-35-960X640.txt /boot/config.txt 
+sudo cp ./usr/cmdline.txt /boot/
+sudo cp ./usr/inittab /etc/
+sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
+sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo cp -rf ./usr/99-calibration.conf-3508 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
+sudo reboot
@@ -1,7 +1,27 @@
+#!/bin/bash
 sudo cp -rf ./boot/config-397.txt /boot/config.txt 
 sudo cp ./usr/cmdline.txt /boot/
 sudo cp ./usr/inittab /etc/
 sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
-sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo mkdir /etc/X11/xorg.conf.d 
 sudo cp -rf ./usr/99-calibration.conf-397 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
 sudo reboot
@@ -1,7 +1,27 @@
+#!/bin/bash
 sudo cp -rf ./boot/config-43.txt /boot/config.txt 
 sudo cp ./usr/cmdline.txt /boot/
 sudo cp ./usr/inittab /etc/
 sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
-sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo mkdir /etc/X11/xorg.conf.d 
 sudo cp -rf ./usr/99-calibration.conf-43 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
 sudo reboot
@@ -1,7 +1,27 @@
+#!/bin/bash
 sudo cp -rf ./boot/config-5.txt /boot/config.txt 
 sudo cp ./usr/cmdline.txt /boot/
 sudo cp ./usr/inittab /etc/
 sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf 
-sudo mkdir -p /etc/X11/xorg.conf.d 
+sudo mkdir /etc/X11/xorg.conf.d 
 sudo cp -rf ./usr/99-calibration.conf-5 /etc/X11/xorg.conf.d/99-calibration.conf 
+nodeplatform=`uname -n`
+kernel=`uname -r`
+version=`uname -v`
+if test "$nodeplatform" = "raspberrypi";then
+echo "this is raspberrypi kernel"
+version=${version%% *}
+version=${version#*#}
+echo $version
+if test $version -lt 970;then
+echo "reboot"
+else
+echo "need to update touch configuration"
+sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
+sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
+echo "reboot"
+fi
+else
+echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
+fi
 sudo reboot
@@ -0,0 +1,34 @@
+
+[version]
+ v1.1
+[Driver installation]
+Step1, Install Raspbian official mirror                                                                     
+1)Download Raspbian official mirror:https://www.raspberrypi.org/downloads/
+2)Use“SDFormatter.exe”to Format your TF Card，
+3)Use“Win32DiskImager.exe” Burning mirror to TF Card。
+Step2, Install LCD Driver                                                                                
+1)Copy “LCD-show-160701.tar.gz” to the root directory of raspberry pi（you can copy it directly to TF card after Step1, or use SFTP to remote copy）
+2)Landing Raspberry pi system to user command line (Name:pi,Password:raspberry)，Execute the following command:
+cd /boot
+sudo tar zxvf LCD-show-160701.tar.gz
+cd LCD-show/
+#For 2.8inch RPI LCD excute:
+sudo ./LCD28-show
+# For 3.2inch RPI LCD excute:
+sudo ./LCD32-show
+# For 3.5inch RPI LCD excute:
+sudo ./LCD35-show
+# For 3.97inch RPI LCD excute:
+sudo ./LCD397-show
+# For 4.3inch RPI LCD excute:
+sudo ./LCD43-show
+# For 5inch RPI LCD excute:
+sudo ./LCD5-show
+# For 7inch(B)-800X480 RPI LCD excute:
+sudo ./LCD7B-show
+# For 7inch(C)-1024X600 RPI LCD excute:
+sudo ./LCD7C-show
+# If you need to switch back to the traditional HDMI display excute:
+Sudo ./LCD-hdmi
+
+3)Wait a few minutes,the system will restart automaticall , enjoy with your LCD.
@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 480 320 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 600 400 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 720 480 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 810 540 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
@@ -0,0 +1,63 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+hdmi_drive=2
+hdmi_force_hotplug=1
+hdmi_group=2
+hdmi_mode=87
+hdmi_cvt 960 640 60 6 0 0 0
+dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
@@ -54,5 +54,5 @@ enable_uart=1

 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
-dtoverlay=tft35a:rotate=90
+dtoverlay=tft35a
 dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=1,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
@@ -0,0 +1,73 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+display_rotate=1 
+dtoverlay=qddpi24     
+overscan_left=0
+overscan_right=0
+overscan_top=0
+overscan_bottom=0
+framebuffer_width=480
+framebuffer_height=320
+enable_dpi_lcd=1
+display_default_lcd=1    
+dpi_group=2
+dpi_mode=87     
+dpi_output_format=0x07f003
+hdmi_timings=321 0 28 18 28 480 0 2 2 4 0 0 0 60 0 32000000 6
+
+dtoverlay=ads7846,cs=1,penirq=18,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
@@ -56,7 +56,7 @@ enable_uart=1
 dtparam=audio=on
 max_usb_current=1
 display_rotate=0
-hdmi_drive=1
+max_usb_current=1
 hdmi_group=2
 hdmi_mode=87
 hdmi_timings=480 0 1 41 2 272 0 2 10 2 0 0 0 60 0 9000000 3
@@ -55,7 +55,6 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
-hdmi_drive=1
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87
@@ -55,7 +55,6 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
-hdmi_drive=1
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87
@@ -55,7 +55,6 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
-hdmi_drive=1
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87
@@ -0,0 +1,6 @@
+Section "InputClass"
+        Identifier      "calibration"
+        MatchProduct    "ADS7846 Touchscreen"
+        Option  "Calibration"   "3945 233 3939 183"
+        Option  "SwapAxes"      "1"
+EndSection