diff --git a/boot/config-28.txt b/boot/config-28.txt
deleted file mode 100755
index cce09e0..0000000
--- a/boot/config-28.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=tft9341:rotate=270
-#dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=0,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-32.txt b/boot/config-32.txt
deleted file mode 100755
index cce09e0..0000000
--- a/boot/config-32.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=tft9341:rotate=270
-#dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=0,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-35-480X320.txt b/boot/config-35-480X320.txt
deleted file mode 100755
index f49123a..0000000
--- a/boot/config-35-480X320.txt
+++ /dev/null
@@ -1,64 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-hdmi_force_hotplug=1
-config_hdmi_boost=7
-hdmi_drive=2
-hdmi_force_hotplug=1
-hdmi_group=2
-hdmi_mode=87
-hdmi_cvt 480 320 60 6 0 0 0
-dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-35.txt b/boot/config-35.txt
deleted file mode 100755
index d51a5eb..0000000
--- a/boot/config-35.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=tft35a
-#dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=1,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-35DPI.txt b/boot/config-35DPI.txt
deleted file mode 100755
index 8e9cecd..0000000
--- a/boot/config-35DPI.txt
+++ /dev/null
@@ -1,73 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-#dtparam=i2c_arm=on
-#dtparam=i2s=on
-#dtparam=spi=on
-
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-
-display_rotate=1 
-dtoverlay=dpi18
-overscan_left=0
-overscan_right=0
-overscan_top=1
-overscan_bottom=1
-framebuffer_width=480
-framebuffer_height=320
-enable_dpi_lcd=1
-display_default_lcd=1
-dpi_group=2
-dpi_mode=87
-dpi_output_format=0x07f205
-hdmi_timings=320 0 28 18 28 480 0 2 2 4 0 0 0 60 0 32000000 6
-
-#dtoverlay=ads7846,cs=1,penirq=18,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-397.txt b/boot/config-397.txt
deleted file mode 100755
index 3152f15..0000000
--- a/boot/config-397.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-display_rotate=3
-max_usb_current=1
-hdmi_force_hotplug=1
-config_hdmi_boost=7
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_drive=2
-hdmi_cvt 480 800 60 6 0 0 0
-dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-43.txt b/boot/config-43.txt
deleted file mode 100755
index 7b6d5c6..0000000
--- a/boot/config-43.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-max_usb_current=1
-display_rotate=0
-max_usb_current=1
-hdmi_group=2
-hdmi_mode=87
-hdmi_timings=480 0 1 41 2 272 0 2 10 2 0 0 0 60 0 9000000 3
-dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-5.txt b/boot/config-5.txt
deleted file mode 100755
index 6bbe075..0000000
--- a/boot/config-5.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-max_usb_current=1
-display_rotate=0
-hdmi_force_hotplug=1
-config_hdmi_boost=7
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_drive=1
-hdmi_cvt 800 480 60 6 0 0 0
-dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
diff --git a/boot/config-7B-800x480.txt b/boot/config-7B-800x480.txt
deleted file mode 100755
index 4846f03..0000000
--- a/boot/config-7B-800x480.txt
+++ /dev/null
@@ -1,64 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-max_usb_current=1
-hdmi_force_hotplug=1
-config_hdmi_boost=7
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_drive=1
-hdmi_cvt 800 480 60 6 0 0 0
diff --git a/boot/config-7C-1024x600.txt b/boot/config-7C-1024x600.txt
deleted file mode 100755
index 0e8c57a..0000000
--- a/boot/config-7C-1024x600.txt
+++ /dev/null
@@ -1,65 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-max_usb_current=1
-hdmi_force_hotplug=1
-config_hdmi_boost=7
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_drive=1
-display_rotate=0
-hdmi_cvt 1024 600 60 6 0 0 0
diff --git a/boot/config-MPI5001.txt b/boot/config-MPI5001.txt
deleted file mode 100755
index a5aa41f..0000000
--- a/boot/config-MPI5001.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-display_rotate=0
-max_usb_current=1
-hdmi_force_hotplug=1
-config_hdmi_boost=7
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_drive=2
-hdmi_force_edid_audio=1
-hdmi_cvt 800 480 60 6 0 0 0
diff --git a/boot/config-mhs24.txt b/boot/config-mhs24.txt
deleted file mode 100755
index 7dd2e2d..0000000
--- a/boot/config-mhs24.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=mhs24
-hdmi_force_hotplug=1
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_cvt 320 240 60 6 0 0 0
-hdmi_drive=2
diff --git a/boot/config-mhs32.txt b/boot/config-mhs32.txt
deleted file mode 100755
index 2b191b6..0000000
--- a/boot/config-mhs32.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=mhs32
-hdmi_force_hotplug=1
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_cvt 480 320 60 6 0 0 0
-hdmi_drive=2
\ No newline at end of file
diff --git a/boot/config-mhs35.txt b/boot/config-mhs35.txt
deleted file mode 100755
index 51b2e27..0000000
--- a/boot/config-mhs35.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=mhs35:rotate=90
-hdmi_force_hotplug=1
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_cvt 480 320 60 6 0 0 0
-hdmi_drive=2
diff --git a/boot/config-mhs395.txt b/boot/config-mhs395.txt
deleted file mode 100755
index b9d3278..0000000
--- a/boot/config-mhs395.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=mhs395
-hdmi_force_hotplug=1
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_cvt 480 320 60 6 0 0 0
-hdmi_drive=2
\ No newline at end of file
diff --git a/boot/config-mis35.txt b/boot/config-mis35.txt
deleted file mode 100755
index fc53c4a..0000000
--- a/boot/config-mis35.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-# For more options and information see
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-dtparam=i2c_arm=on
-#dtparam=i2s=on
-dtparam=spi=on
-enable_uart=1
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-dtoverlay=mis35
-hdmi_force_hotplug=1
-hdmi_group=2
-hdmi_mode=1
-hdmi_mode=87
-hdmi_cvt 480 320 60 6 0 0 0
-hdmi_drive=2
diff --git a/usr/40-libinput.conf-HDMI7B b/usr/40-libinput.conf-HDMI7B
deleted file mode 100755
index 2207d9d..0000000
--- a/usr/40-libinput.conf-HDMI7B
+++ /dev/null
@@ -1,36 +0,0 @@
-# Match on all types of devices but tablet devices and joysticks
-Section "InputClass"
-        Identifier "libinput pointer catchall"
-        MatchIsPointer "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput keyboard catchall"
-        MatchIsKeyboard "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput touchpad catchall"
-        MatchIsTouchpad "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput touchscreen catchall"
-        MatchIsTouchscreen "on"
-	Option "CalibrationMatrix" "1 0 0 0 1 0 0 0 1"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput tablet catchall"
-        MatchIsTablet "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
diff --git a/usr/40-libinput.conf-HDMI7C b/usr/40-libinput.conf-HDMI7C
deleted file mode 100755
index 2207d9d..0000000
--- a/usr/40-libinput.conf-HDMI7C
+++ /dev/null
@@ -1,36 +0,0 @@
-# Match on all types of devices but tablet devices and joysticks
-Section "InputClass"
-        Identifier "libinput pointer catchall"
-        MatchIsPointer "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput keyboard catchall"
-        MatchIsKeyboard "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput touchpad catchall"
-        MatchIsTouchpad "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput touchscreen catchall"
-        MatchIsTouchscreen "on"
-	Option "CalibrationMatrix" "1 0 0 0 1 0 0 0 1"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection
-
-Section "InputClass"
-        Identifier "libinput tablet catchall"
-        MatchIsTablet "on"
-        MatchDevicePath "/dev/input/event*"
-        Driver "libinput"
-EndSection