Add files via upload

boot/config-35-480X320.txt

@@ -54,7 +54,8 @@ enable_uart=1
 
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
-
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_drive=2
 hdmi_force_hotplug=1
 hdmi_group=2

boot/config-35-600X400.txt

@@ -54,7 +54,8 @@ enable_uart=1
 
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
-
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_drive=2
 hdmi_force_hotplug=1
 hdmi_group=2

boot/config-35-720X480.txt

@@ -54,7 +54,8 @@ enable_uart=1
 
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
-
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_drive=2
 hdmi_force_hotplug=1
 hdmi_group=2

boot/config-35-810X540.txt

@@ -54,7 +54,8 @@ enable_uart=1
 
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
-
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_drive=2
 hdmi_force_hotplug=1
 hdmi_group=2

boot/config-35-960X640.txt

@@ -54,7 +54,8 @@ enable_uart=1
 
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
-
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_drive=2
 hdmi_force_hotplug=1
 hdmi_group=2

boot/config-397.txt

@@ -56,6 +56,8 @@ enable_uart=1
 dtparam=audio=on
 display_rotate=3
 max_usb_current=1
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87

boot/config-5.txt

@@ -55,6 +55,8 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87

boot/config-7B-800x480.txt

@@ -55,9 +55,10 @@ enable_uart=1
 # Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 max_usb_current=1
+hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87
 hdmi_drive=1
 hdmi_cvt 800 480 60 6 0 0 0
-#dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900

boot/config-7C-1024x600.txt

@@ -56,6 +56,7 @@ enable_uart=1
 dtparam=audio=on
 max_usb_current=1
 hdmi_force_hotplug=1
+config_hdmi_boost=7
 hdmi_group=2
 hdmi_mode=1
 hdmi_mode=87

boot/config-MPI5001.txt

@@ -0,0 +1,64 @@
+# For more options and information see
+# http://www.raspberrypi.org/documentation/configuration/config-txt.md
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+enable_uart=1
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+max_usb_current=1
+hdmi_force_hotplug=1
+config_hdmi_boost=7
+hdmi_group=2
+hdmi_mode=1
+hdmi_mode=87
+hdmi_drive=1
+hdmi_cvt 800 480 60 6 0 0 0